Search Results

Wall Mount FIX-028 TABLE MOUNT FIX-030 TABLE MOUNT WALL MOUNT You can purchase the Wall Mount accessory to mount the display on a concrete or wooden wall. To mount the display on the wall, follow these steps: 1. Disconnect the AC power adaptor from the power source to turn off the display. 2. Lay the display face down on a flat surface. CAUTION: Always use a soft material, cloth or foam, to protect the display when placing the screen face down. 3. Mount the monitor bracket at the back of the display. Secure the bracket with four M4x12 bolts and washers. 4. Place the wall plate on the wall and mark the four mounting holes. 5. Perform one of the following: • For a concrete wall, drill four 8 mm holes on the concrete wall, and insert an anchor into each hole. • For wooden mount, drill two 3.8 mm holes on the wood, and insert an anchor into each hole. 6. Align the wall plate with the mounting holes. Secure the plate to the wall with lag bolts and log bolt washers. CONCRETE WALL WOODEN WALL 7. Align the display with the wall plate, and then carefully slide down the display until the bracket is safely secured to the wall plate. 8. Secure the bracket to the wall plate with two M5x15 bolts and M5 washers. 9. Plug the AC power adaptor into a power source to turn on the display. FIX-028 TABLE MOUNT To install the FIX-028 table mount to the display, follow these steps: 1. Disconnect the AC power adaptor from the power source to turn off the display. 2. Pull up the stand from the base and the VESA plate from the stand. 3. Lay the display face down on a flat surface. CAUTION : Always use a soft material, cloth or foam, to protect the display when placing the screen face down. 4. Mount the VESA plate at the back of the display. Secure the VESA plate with four M4x12 bolts and washers. 5. Set the display in an upright position. 6. Connect the AC power adaptor into a power source to turn on the display. FIX-030 TABLE MOUNT The FIX-030 table mount can be installed using a weighted or grommet base. To install the FIX-030 table mount to the display, follow these steps: 1. Disconnect the AC power adaptor from the power source to turn off the display. 2. Install the Pole to the Weighted Base or to the Grommet Base, and secure with three M5 x 14 bolts using an Allen Key. For a Grommet Base, attach a soft pad at the base. NOTE : If an existing grommet hole comes with a plastic protector, remove it to ensure to have a flat surface before installing the table mount. 3. To install the table mount to a hole in a desk, drill a 10 mm hole and secure the mount with a Support Plate, M10 Washer, Spring Washer, and M10 Bolt using a wrench. 4. Install the Monitor Arm to the pole. Fasten the bolt with an Allen Key. Attach the Wire Clip to the pole. 5. Install the VESA Plate at the back of the display, and then secure it with four M4 x 12 thumbscrews. 6. Slide down the display carefully until the plate locks into the head of the monitor arm, and then secure the display with a M4 x 6 bolt. 7. Fasten the Grub Screw in the monitor arm to fix the tilting angle using an Allen Key. 8. Route the cables out the display and through the Wire Clip.

Copyright & Disclaimer Safety Instructions Magnetar Product Overview Magnetar Features Magnetar Product Specifications Windows Platform Android Platform Magnetar Input/Output Ports Magnetar Dimensions Magnetar Label Locations Magnetar Installation and Setup Installing Display to Kiosk Installing Wall Mount Magnetar User Manual PDF PRODUCT OVERVIEW The Glory Star Magnetar Weatherproof Touch Screen is IP65 rated with a dust and water resistant front glass. The touch screen comes with a high-brightness screen and fingerprint and scratch resistant surface, making it a true industrial grade solution. It is cost-effective for system integrators who require a reliable product for indoor and outdoor applications. Offering flexibility, the display can be integrated to a kiosk, point-of-sale (POS), or mounted to the wall. The display can be installed in portrait, landscape, or face-up orientation. With Star Control, you can remotely manage all Glory Star devices at the same time, systematically update and manage user requests in one single Android platform. FEATURES Up to 1000 nits brightness that provides exceptional color performance even when placed outdoors Equipped with optional, adjustable, external mounting brackets IP65 rating for dust and water resistant front glass Supports touch-on-water that allows you to activate the touch screen even when water is spilled on the touch glass or with latex gloves Scratch and fingerprint resistant 6H scratch-resistant touch glass to withstand demanding applications Landscape, portrait, and face up orientation PRODUCT SPECIFICATIONS WINDOWS PLATFORM ANDROID PLATFORM

WHAT'S INCLUDED IN THE BOX 1 x RFID module 1 x USB to Type C connector 2 x Screws DOWNLOADING THE DEVELOPMENT KIT Download the development kit at www.elatec.com/devpack406 . What's Included in the Box Rewriting RFID Standards Configuring RFID for Touch Screen INSTALLATION INSTRUCTIONS: Nebula Kiosk Tablet Nebula Plus Computer Tablet Ultron Touchscreen Computer NEBA1703 RFID (Windows) PDF RFID/NFC REWRITING THE RFID STANDARDS STEP 1: CHECKING YOUR RFID CARD TYPE NOTE: If you already know your card type, please skip this step. 1. Prepare your RFID card. 2. Connect t he Glory Star RFID module to your computer through the USB port only. Connect the external USB to the NEB1703 USB Type C connector to PC port. 3. From th e developer pack, select Director.exe . NOTE: This is only support ed on Windows PC. 4. Select Connect . The statu s displays Connected to USB (COM) . 5. Place the card into the NEB1703 RFID. 6. Select Search Tag . The RFID card type is displayed. STEP 2: WRITING RFID STANDARDS TO NEBA1703 1. Connect the Glory Star RFID module to your computer through the USB port only. Connect the external USB to the NEB1703 USB Type C connector to PC port. 2. From the developer pack, select AppBlaster.exe . NOTE: This is only supported on Windows PC. 3. Select Configurable project . 4. Select one of the following: • For keyboard mode, select Multi Keyboard V4.06. App Standard V2.04 . • For read and write mode, select Multi CDC V4.06. App Standard V2.04 . 5. Select Select Template . 6. Select Transponder Types , and then add your RFID card type. 7. Select Create Image . 8. Select Program Image . STEP 3: FINDING API 1. Select R ead and Write Mode before adding configuration. 2. Select Docs → TWN4 Simple Protocol DocRev24 to see list of developer commands. STEP 4: INSTALLING THE RFID MODULE TO DISPLAY Select the display to install and follow the corresponding procedure. Nebula Kiosk Tablet Nebula Plus Computer Tablet Ultron Touchscreen Computer STEP 5: TESTING THE RFID CARD ON THE NEBA1703ECC RFID MODULE Use the Star Tool Demo APK installed on the device to test your RFID card. If you don’t have it, please contact sales@glorystargroup.com . 1. Open the Star Tool Demo APK app. 2. From the Modules section, select RFID . 3. Scan your RFID card on the RFID module. Use an RFID card that supports the RFID standards listed under All supported transponders . Your card type and card ID information are displayed. CONFIGURING RFID FOR TOUCH SCREEN DEVICES 1. Launch the Star Tool app. 2. From the Addon Modules category, select Enter . 3. Select RFID module . 4. Hover an RFID card on the RFID module, and then select Scan card . The Card type and Card ID are displayed. 5. To change the RFID value, type an RFID value , and then select Write value . 6. Select Read card to check new RFID card value. NEBULA KIOSK RFID/NFC Before installing the RFID to your kiosk tablet, configure the module first. INSTALLING MODULE 1. Connect the RFID/NFC module to a Micro USB port of the tablet. 2. Secure the RFID/NFC module with two screws. NEBULA PLUS RFID/NFC Before installing the RFID to your kiosk tablet, configure the module first. INSTALLING MODULE 1. Connect the RFID/NFC module to a USB Type C port of the tablet. 2. Secure the RFID/NFC module with two screws. ULT RON TOUCHSCRE EN COMPUTER Before installing the RFID to your kiosk tablet, configure the module first. INSTALLING MODULE 1. Connect the RFID/NFC module to a USB port of the tablet. 2. Secure the RFID/NFC module with two screws.

SUPPORTED PRODUCTS: Nebula Kiosk Tablet Nebula Plus Computer Tablet Ultron Touchscreen Computer REFERENCES Barcode Scanner QSG (Honeywell) 2D Barcode Scanner (Honeywell) Barcode Scanner QSG (Newland) 1D Barcode Scanner (Newland) NEBULA KIOSK 1D/2D SCANNER INSTALLING MODULE 1. Connect the 1D/2D barcode scanner module to a USB port of the tablet. 2. Secure the 1D/2D barcode scanner module with two screws. NEBULA PLUS 1D/2D SCANNER INSTALLING MODULE 1. Connect the 1D/2D barcode scanner module to a USB Type C port of the tablet. 2. Secure the 1D/2D barcode scanner module with two screws. ULTRON 1D/2D SCANNER INSTALLING MODULE 1. Connect the 1D/2D barcode scanner module to a USB port of the tablet. 2. Secure the 1D/2D barcode scanner module with two screws. CONFIGURING MODULE 1. Launch the Star Tool app. 2. From the Addon Modules category, select Enter . 3. Select Barcode modules . 4. Select the installed barcode scanner. 5. Select Keyboard or Serial as the input mode for barcodes. The barcode displays in the Scanned output field. 6. Select one of the following: • Light modes On – always turns on the barcode scanner light. • Light modes Auto – turns on the barcode scanner light when it detects a barcode to scan. • Light modes Off – turns off the barcode scanner light. 7. To add a line break after scanning a barcode, enable Automatically return . 8. To add a beep sound after scanning a barcode, enable Sound notification . 9. To view the list of 1D and 2D supported barcodes, select the format type under Supported format .

Welcome to Glory Star Online Help LEARN MORE ABOUT THE SITE Magnetar Weatherproof Touchscreen VegaX Intercom System Vega Gen 2 In-Wall Indoor Touchscreen NEBULA KIOSK TABLET NEBULA PLUS TABLET NEBULA GLOW MEETING ROOM TOUCHSCREEN Infinitus Touchscreen Signage Ultron Touchscreen Computer STAROS VEGAOS INDOOR STAR CONTROL STAR TOOL VEGAOS OUTDOOR

Copyright & Disclaimer Safety Instructions Ultron Product Overview Ultron Features Ultron Product Specifications Ultron Input/Output Ports Ultron Label Locations Ultron Dimensions Ultron Installation and Setup Ultron User Manual PDF ULTRON TOUCHSCREEN COMPUTER USER MANUAL PRODUCT OVERVIEW ULTRON Windows Touchscreen Computer is a commercial grade, multi-purpose, fixed tablet in 10-inch, 15.6-inch and 21.5-inch. Designed to integrate key peripherals and display systems easily for diversified self-service and touch display terminal. It has a durable metal form factory and an enterprise infrastructure with a powerful Windows based platform. With mounting options in table top, wall, and floor stand, ULTRON Touchscreen Computer is deal for self-service applications in retail, fitness, manufacturing, and hospitality environments. Learn More on Features and Specifications INSTALLATION AND SETUP Select a preferred configuration for the display before installing the product and setting it up for use. CAUTION: Follow the installation instructions properly to avoid dropping and damaging the display. CONFIGURATIONS Learn How to Install the Device

Copyright & Disclaimer Safety Instructions Ultron Product Overview Ultron Features Ultron Product Specifications Ultron Input/Output Ports Ultron Label Locations Ultron Dimensions Ultron Installation and Setup Ultron User Manual PDF INSTALLATION AND SETUP Select a preferred configuration for the display before installing the product and setting it up for use. CAUTION: Follow the installation instructions properly to avoid dropping and damaging the display. CONFIGURATIONS UNPACKING THE BOX Out of the Box Failure If you experience an out of box failure (OBF) during installation in relation to missing, incorrect, or defective unit or item, send an email to support@glorystargroup.com and provide a description of the issue. Glory Star will first troubleshoot the problem over phone or video to help resolve the issue. If Glory Star determines that a product or component has to be returned to the factory, it will instruct the customer how to remove the components from the product. INSTALLING MODULES You can install the following modules to the computer tablet: RFID/NFC RFID/NFC – automatically identifies persons and conducts access management and mobile payments 1D/2D Barcode Scanner 1D/2D Barcode Scanner – scans printed barcodes and captures data information INSTALLING WALL MOUNT You can purchase the Wall Mount accessory to mount the display on a concrete or wooden wall. Wall Mount INSTALLING TABLE MOUNT You can purchase the FIX-028 and FIX-030 table mounts for the display. FIX-028 FIX-030

Copyright & Disclaimer Safety Instructions Ultron Product Overview Ultron Features Ultron Product Specifications Ultron Input/Output Ports Ultron Label Locations Ultron Dimensions Ultron Installation and Setup Ultron User Manual PDF PRODUCT OVERVIEW ULTRON Windows Touchscreen Computer is a commercial grade, multi-purpose, fixed tablet in 10-inch, 15.6-inch and 21.5-inch. Designed to integrate key peripherals and display systems easily for diversified self-service and touch display terminal. It has a durable metal form factory and an enterprise infrastructure with a powerful Windows based platform. With mounting options in table top, wall, and floor stand, ULTRON Touchscreen Computer is deal for self-service applications in retail, fitness, manufacturing, and hospitality environments. FEATURES Durable Fanless 10K Times of Stress Test PRODUCT SPECIFICATIONS J6412 i3-1215U i5-1235U

Copyright & Disclaimer Safety Instructions Ultron Product Overview Ultron Features Ultron Product Specifications Ultron Dimensions Ultron Label Locations Ultron Installation and Setup Ultron User Manual PDF DIMENSIONS 10" DISPLAY 10" DISPLAY WITH PERIPHERALS 15.6" DISPLAY 15.6" DISPLAY WITH PERIPHERALS 21.5" DISPLAY 21.5" DISPLAY WITH PERIPHERALS INPUT/OUTPUT PORTS LABEL LOCATION

MAGNETAR Weatherproof Touchscreen NEBULA Kiosk Tablet NEBULA PLUS Computer Tablet NEBULA GLOW Meeting Room Tablet ULTRON Touchscreen Computer VEGA X Intercom System VEGA Gen 2 In-Wall Indoor Touchscreen INFINITUS Touchscreen Signage SAFETY INSTRUCTIONS IMPORTANT: Read the user manual first before installing, using, or maintaining the display. Save the user manual in a safe place for future reference. WARNING: Install the product properly to avoid dropping and damaging the display. Store or use the display in a safe location. WARNING: The power supply cord should be connected to a socket-outlet with an earthing connection. WARNING: Disconnect the AC power cord before opening the unit to install features or service the product. Do not connect or disconnect any peripheral while the product is connected to AC power. This can result in system damage. WARNING: Operate the product only within -30 °C to 60 °C. WARNING: Avoid collision of the display with other objects. WARNING: Avoid leaking or dropping liquid to the touch screen that may cause damage and malfunction to the display. WARNING: Do not disassemble the display and power adaptor to avoid electric shock and fire. This would void the warranty terms. WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type as recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. WARNING: Do not overload the electric socket; it may cause fire or explosion. Be cautious of whether the local voltage is compatible with the power adaptor input voltage. WARNING: Repair or replace damaged or worn cords immediately. WARNING: Avoid pulling the power cord when unplugging the display. Carefully disconnect the cable from the port to prevent damage to your power cord. WARNING: Risk of electric shock. Do not remove the cover. WARNING: Screw lengths inside the cover should not be longer than 8 mm. VEGA X SAFETY INSTRUCTIONS Read this user manual All safety and operating instructions in this user manual should be read before operating the product. Keep this user manual This user manual should be retained for future references. Head Warnings Be cautious about warning signals on the product. Follow Instructions Please follow instructions in this user manual. Attachments To avoid danger, please do not use attachments not recommended by the product manufacturer. Mounting Do not place the product on any unstable cart, stand, tripod or table to avoid injury on children and adult. Please only use attachments indicated by product manufacturer. Temperature Please use this product within operating temperature 32°F ~ 100°F (0°C ~ 45°C), relative humidity 20%-80%. The product should be situated away from any heat source such as radiators, heat registers, stoves or other products (including amplifier) to product heat. Avoid Liquid Invasion Avoid the invasion of any liquid. Avoid placing it near bathtub, sink, kitchen, wet basement, or swimming pool. Do not place product on any uneven surface and keep a distance of at least 6 inches from the wall. Avoid over heat Do not place heavy objects on top of the unit and at sealed areas to avoid heat ventilation problems. Product Protection Please do not place any attachment or parts inside the product to avoid contact with voltage points that could result in electric shock or fire. Heat Ventilation There is no heat ventilation on the upper and lower parts of the product, therefore to avoid overheating, please do not block any ventilation openings with objects (e.g. carpet). Please allow the opening to have 10 cm distance for ventilation. Grounding or Polarization The product could be equipped with an alternate plug. Power – Cord Protection Power supply cords should be routed so that they are unlikely to be walked on or pitched by items placed upon them. Pay attention to the connection of plugs. Power Sources The product should be operated only from the type of power source indicated on the rear panel. If you are unsure of the type of power supply of your home, consult your product purchaser or local power company. Lighting and storms Unplug the product from the wall outlet during lighting, storms, or long unused periods. This will prevent damages and power-line surges to the product.   Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. Damage Handling Unplug the product from the outlet of the wall and request qualified service personnel under the following conditions: • When the power supply cord or plug is damaged • When the picture display gets dimmer • When liquid has been spilled or objects have fallen on to the product • When the product has been exposed to rain or water. • Adjust only those controls that are in the instruction manual. Improper adjustments may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. • When the product exhibits a distinct change in performance – this indicates a need for repair service. Replacement parts When replacement parts are required, be sure that the technician uses replacement parts specified by the manufacturer or parts with same features. Unauthorized substitution may result in fire, electric shock, or other hazards. Safety Check Upon completion of any service or repair to this product, ensure technician performs safety checks for proper operating condition. Warnings If the battery of remote control is incorrectly replaced, there will be danger of explosion. Storage Keep the product at dim areas, room temperature, and low humidity to maintain original condition and avoid danger. Transportation Since the product consists of glass and delicate electronic components, excessive shock or drop will result in damages. Please handle the product carefully to minimize shock during transportation. Recycling The product utilizes tin-lead solder, and has a fluorescent lamp containing a small amount of mercury. For environmental considerations, disposal of these materials may be regulated in your community. For disposal or recycling information, please contact your local authorities, or Electronics Industries Alliance: http://www.eiae.org/. Cleaning Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use damp cloth for cleaning. INFINITUS SAFETY INSTRUCTIONS Read this user manual All safety and operating instructions in this user manual should be read before operating the product. Keep this user manual This user manual should be retained for future references. Head Warnings Be cautious about warning signals on the product. Follow Instructions Please follow instructions in this user manual. Attachments To avoid danger, please do not use attachments not recommended by the product manufacturer. Mounting Do not place the product on any unstable cart, stand, tripod or table to avoid injury on children and adult. Please only use attachments indicated by product manufacturer. Temperature Please use this product within operating temperature 32°F ~ 100°F (0°C ~ 45°C), relative humidity 20%-80%. The product should be situated away from any heat source such as radiators, heat registers, stoves or other products (including amplifier) to product heat. Avoid Liquid Invasion Avoid the invasion of any liquid. Avoid placing it near bathtub, sink, kitchen, wet basement, or swimming pool. Do not place product on any uneven surface and keep a distance of at least 6 inches from the wall. Avoid over heat Do not place heavy objects on top of the unit and at sealed areas to avoid heat ventilation problems. Product Protection Please do not place any attachment or parts inside the product to avoid contact with voltage points that could result in electric shock or fire. Heat Ventilation There is no heat ventilation on the upper and lower parts of the product, therefore to avoid overheating, please do not block any ventilation openings with objects (e.g. carpet). Please allow the opening to have 10 cm distance for ventilation. Grounding or Polarization The product could be equipped with an alternate plug. Power – Cord Protection Power supply cords should be routed so that they are unlikely to be walked on or pitched by items placed upon them. Pay attention to the connection of plugs. Power Sources The product should be operated only from the type of power source indicated on the rear panel. If you are unsure of the type of power supply of your home, consult your product purchaser or local power company. Lighting and storms Unplug the product from the wall outlet during lighting, storms, or long unused periods. This will prevent damages and power-line surges to the product.   Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. Damage Handling Unplug the product from the outlet of the wall and request qualified service personnel under the following conditions: • When the power supply cord or plug is damaged • When the picture display gets dimmer • When liquid has been spilled or objects have fallen on to the product • When the product has been exposed to rain or water. • Adjust only those controls that are in the instruction manual. Improper adjustments may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. • When the product exhibits a distinct change in performance – this indicates a need for repair service. Replacement parts When replacement parts are required, be sure that the technician uses replacement parts specified by the manufacturer or parts with same features. Unauthorized substitution may result in fire, electric shock, or other hazards. Safety Check Upon completion of any service or repair to this product, ensure technician performs safety checks for proper operating condition. Warnings If the battery of remote control is incorrectly replaced, there will be danger of explosion. Storage Keep the product at dim areas, room temperature, and low humidity to maintain original condition and avoid danger. Transportation Since the product consists of glass and delicate electronic components, excessive shock or drop will result in damages. Please handle the product carefully to minimize shock during transportation. Recycling The product utilizes tin-lead solder, and has a fluorescent lamp containing a small amount of mercury. For environmental considerations, disposal of these materials may be regulated in your community. For disposal or recycling information, please contact your local authorities, or Electronics Industries Alliance: http://www.eiae.org/. Cleaning Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use damp cloth for cleaning.

INSTALLATION & SETUP Select a preferred configuration for the display before installing the product and setting it up for use. CAUTION: Follow the installation instructions properly to avoid dropping and damaging the display. Mounting Options MOUNTING OPTIONS Copyright & Disclaimer Vega X Safety Instructions Vega X Product Overview Vega X Features Vega X Product Specifications Vega X Input Output Ports Vega X Label Locations Vega X Dimensions Vega X Installation Mounting Options Vega X Unpacking the Box Performing Pre-Installation Tasks Mounting the Device to the Wall Vega X User Manual PDF UNPACKING THE BOX Out of the Box Failure If you experience an out of box failure (OBF) during installation in relation to missing, incorrect, or defective unit or item, send an email to support@glorystargroup.com and provide a description of the issue. Glory Star will first troubleshoot the problem over phone or video to help resolve the issue. If Glory Star determines that a product or component has to be returned to the factory, it will instruct the customer how to remove the components from the product. PERFORMING PRE-INSTALLATION TASKS Before installing the device to the wall mount, perform the following tasks first: 1. Copy the serial number from back of the device. 2. Prepare a connected POE or 12V input cable. 3. Connect the panel’s relay to the building’s door strike or access control system. 4. Load the software and compatible firmware first to the device. The device software or firmware is updated using the micro USB port located at the back of the device. Once installed, you need to uninstall the device from the wall mount before you can update the software or firmware. MOUNTING THE DEVICE TO THE WALL To mount the device to the wall, follow these steps: 1. Place the wall mount on the wall and mark the six mounting holes. 2. Drill six 30 mm holes on the concrete wall, and insert an anchor into each hole. 3. Route the POE cable out of the wall mount. 4. Align the wall mount with the mounting holes. Secure the mount to the wall with screws. 5. Connect the POE cable to the Ethernet with POE port of the device. 6. Connect the other cables to the corresponding ports. 7. Place the Vega X unit into the wall mount. 8. Open the front cover, and then secure the unit with screws. 9. Close and secure the front cover. 10. Go to the Android Settings , and select a Wi-Fi connection .

GET STARTED LEARN WHAT INFORMATION IS AVAILABLE FOR YOUR PRODUCTS Glory Star Online Help Welcome to the Glory Star Online Help site! Browse through the different user manuals of the Glory Star products and access the latest documentation and references to help you set up your device. Installation Instructions Each user manual includes a step-by-step installation procedure for the different configurations available for the product. Features and Product Specifications You can conveniently check the different features and the specifications of each product so you can check the capacity of your device and compare which product would suit your business needs. Troubleshooting Troubleshooting tips and FAQs will be added to guide you in resolving issues.